| Wind Turbine Technology Trends M Bošnjaković, M Katinić, R Santa, D Marić Applied Sciences 12 (17), 8653, 2022 | 52 | 2022 |
| Analysis of heat-affected zone microstructures of steel P92 after welding and after post-weld heat treatment M Dunđer, T Vuherer, I Samardžić, D Marić The International Journal of Advanced Manufacturing Technology 102 (9-12 …, 2019 | 19 | 2019 |
| Correlation between Emission and Combustion Characteristics with the Compression Ratio and Fuel Injection Timing in Tribologically Optimized Diesel Engine S Milojević, S Savić, D Marić, O Stopka, B Krstić, B Stojanović Tehnički vjesnik 29 (4), 1210-1219, 2022 | 18 | 2022 |
| Influence of vibrations on residual stresses distribution in welded joints I Samardžić, T Vuherer, D Marić, P Konjatić Metalurgija 54 (3), 527-530, 2015 | 12 | 2015 |
| Modeling and Optimization of Cut Quality Responses in Plasma Jet Cutting of Aluminium Alloy EN AW-5083 I Peko, D Marić, B Nedić, I Samardžić Materials 14 (19), 5559, 2021 | 10 | 2021 |
| Testing of the shopprimer’s influence on the quality of welded joint T Šolić, D Marić, Ž Jagodić, I Samardžić Metalurgija 56 (3-4), 357-360, 2017 | 6 | 2017 |
| The Impact of Lubricant Viscosity and Materials on Power Losses and Efficiency of Worm Gearbox A Skulić, S Milojević, D Marić, L Ivanović, B Krstić, M Radojković, ... Tehnički vjesnik 29 (6), 1853-1860, 2022 | 5 | 2022 |
| Optimization of Parameters for Protection of Materials by Primer Application T Šolić, D Marić, D Novoselović, I Samardžić Coatings 12 (3), 413, 2022 | 5 | 2022 |
| Application of SVM Models for Classification of Welded Joints D Marić, M Duspara, T Šolić, I Samardžić Tehnički vjesnik 26 (2), 533-538, 2019 | 5 | 2019 |
| Influence of abrasive feeding and cutting direction on the surface roughness M Duspara, T Palatinuš, I Samardžić, D Marić, V Starčević, A Stoić Procedia Engineering 149, 48-55, 2016 | 5 | 2016 |
| Optimization of Synchropulsed MIG Welding Process Parameters for Welding of AW 5083 Sheets L Maglić, D Marić, T Šolić, I Samardžić Materials 15 (9), 3078, 2022 | 4 | 2022 |
| Post-Weld Heat Treatment of S690QL1 Steel Welded Joints: Influence on Microstructure, Mechanical Properties and Residual Stress D Tomerlin, D Marić, D Kozak, I Samardžić Metals 13 (5), 999, 2023 | 3 | 2023 |
| Solving the Problem of Friction and Wear in Auxiliary Devices of Internal Combustion Engines on the Example of Reciprocating Air Compressor for Vehicles S Milojević, S Savić, S Mitrović, D Marić, B Krstić, B Stojanović, V Popović Tehnički vjesnik 30 (1), 122-130, 2023 | 3 | 2023 |
| Statistical analysis of MAG-CMT welding parameters and their influence on the Ni-alloy weld overlay quality on 16Mo3 base material D Marić, T Šolić, V Kondić, I Samardžić Welding in the World 66 (4), 815-831, 2022 | 3 | 2022 |
| Quality Analysis of AISI 321 Welds of Bellow Compensators Used in Shipbuilding D Marić, J Cumin, T Šolić, I Samardžić Journal of Marine Science and Engineering 10 (4), 452, 2022 | 3 | 2022 |
| New Approach of Recycling of Abrasives for Water Jet Cutting M Duspara, T Palatinuš, D Marić, I Samardžić, Ž Ivandić, A Stoić Advances in Manufacturing Engineering and Materials: Proceedings of the …, 2019 | 3 | 2019 |
| Investigation of the Parameters Effects on the Kerf Width in Plasma Jet Cutting Process of Aluminium 5083 using Fuzzy Logic Technique I Peko, D Marić, M Dragičević, T Šolić Proceedings of the 10th International Scientific and Expert Conference TEAM …, 2022 | 2 | 2022 |
| Fuzzy Logic Modelling of Dross Height in Plasma Jet Cutting of Shipbuilding Aluminium Alloy 5083 I Peko, D Marić, T Šolić, T Matić, M Samardžić, I Samardžićb Proceedings of the 10th International Scientific and Expert Conference TEAM …, 2022 | 2 | 2022 |
| Influence of Anticorrosive Pigment, Dry-Film Thickness and Conditioning Time on Protective Properties of Two-Component Epoxy Primer T Šolić, D Marić, I Peko, I Samardžić Materials 15 (9), 3041, 2022 | 2 | 2022 |
| Analysis of plated layer’s effects on the structure resistance to corrosion T Šolić, D Marić, M Duspara, I Samardžić Metalurgija 57 (4), 327-329, 2018 | 2 | 2018 |
